Powered by GadBall Jobs

Joseph Aleman

Address: 205 North Gabreil St. Granger, TX 76530
Telephone: 512-365-4536

MECHANICALLY INCLINED. TRUSTWORTHY AND HARD WORKING INDIVISUAL LOOKING TO BROADEN HIS HORIZONS AND EXTEND EXPERIENCE IN THE HVAC TRADE. PASSIONATE ABOUT WORKING HARD TO EARN MY LIVING.

Experience

Alamo Austin Air


Service technician/Installer - June 2017 - Present

  • Determine project requirements, including scope, assembly sequences, and required methods and materials, according to blueprints, drawings, and written or verbal instructions.
  • Lay out, measure, and mark dimensions and reference lines on material, such as roofing panels, according to drawings or templates, using calculators, scribes, dividers, squares, and rulers.
  • Maneuver completed units into position for installation, and anchor the units.
  • Convert blueprints into shop drawings to be followed in the construction and assembly of sheet metal products.
  • Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, and down spouts, in supportive frameworks.
  • Select gauges and types of sheet metal or non-metallic material, according to product specifications.
  • Test electrical circuits and components for continuity, using electrical test equipment.
  • Reassemble and test equipment following repairs.
  • Discuss heating-cooling system malfunctions with users to isolate problems or to verify that malfunctions have been corrected.
  • Record and report all faults, deficiencies, and other unusual occurrences, as well as the time and materials expended on work orders.
  • Test pipe or tubing joints and connections for leaks, using pressure gauge or soap-and-water solution.
  • Install, connect, and adjust thermostats, humidistats and timers, using hand tools.
  • Assemble, position and mount heating or cooling equipment, following blueprints.
  • Study blueprints, design specifications, and manufacturers' recommendations to ascertain the configuration of heating or cooling equipment components and to ensure the proper installation of components.
  • Fabricate, assemble and install duct work and chassis parts, using portable metal-working tools and welding equipment. Start ups and air balance as well.
  • *** EXPERIENCE IN MINI SPLITS, MITSUBISHI, DAIKIN, GOODMAN.
  • *** EXPERIENCE ALSO IN LENNOX HARMONY 3 ZONE BOARDS, ICOMFORT THERMOSTATS, I-HARMONY ZONE BOARDS, ALL THE LENNOX COMMUICATING SYSTEMS.
  • *** ALSO EXPERIENCE IN ALL OTHER AC EQUIPMENT.
  • *** ON CALL ROTATION, EPA CERT. TYPE 1,2-, TDLR REG.

Austin Air Cond.


Service tech. - March 2014 - June 2017

  • Determine project requirements, including scope, assembly sequences, and required methods and materials, according to blueprints, drawings, and written or verbal instructions.
  • Lay out, measure, and mark dimensions and reference lines on material, such as roofing panels, according to drawings or templates, using calculators, scribes, dividers, squares, and rulers.
  • Maneuver completed units into position for installation, and anchor the units.
  • Convert blueprints into shop drawings to be followed in the construction and assembly of sheet metal products.
  • Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, and down spouts, in supportive frameworks.
  • Select gauges and types of sheet metal or non-metallic material, according to product specifications.
  • Test electrical circuits and components for continuity, using electrical test equipment.
  • Reassemble and test equipment following repairs.
  • Discuss heating-cooling system malfunctions with users to isolate problems or to verify that malfunctions have been corrected.
  • Record and report all faults, deficiencies, and other unusual occurrences, as well as the time and materials expended on work orders.
  • Test pipe or tubing joints and connections for leaks, using pressure gauge or soap-and-water solution.
  • Install, connect, and adjust thermostats, humidistats and timers, using hand tools.
  • Assemble, position and mount heating or cooling equipment, following blueprints.
  • Study blueprints, design specifications, and manufacturers' recommendations to ascertain the configuration of heating or cooling equipment components and to ensure the proper installation of components.
  • Fabricate, assemble and install duct work and chassis parts, using portable metal-working tools and welding equipment. Start ups and air balance as well.
  • *** EXPERIENCE IN MINI SPLITS, MITSUBISHI, DAIKIN, GOODMAN.
  • *** EXPERIENCE ALSO IN LENNOX HARMONY 3 ZONE BOARDS, ICOMFORT THERMOSTATS, I-HARMONY ZONE BOARDS, ALL THE LENNOX COMMUICATING SYSTEMS.
  • *** ALSO EXPERIENCE IN ALL OTHER AC EQUIPMENT.
  • *** ON CALL ROTATION, EPA CERT. TYPE 1,2-, TDLR REG.

Texas Quality Services


lead installer/service tech/rough installer - June 2010 - March 2014

  • Start up units at jobs sites, install t-stat wire, duct detectors , set roof top units in commercial job sites,also residential installer and tech,balance and charge units.
  • Obtain and maintain required certifications.
  • Comply with all applicable standards, policies, and procedures, including safety procedures and the maintenance of a clean work area.
  • Repair or replace defective equipment, components, or wiring.
  • Test electrical circuits and components for continuity, using electrical test equipment.
  • Reassemble and test equipment following repairs.
  • Inspect and test system to verify system compliance with plans and specifications and to detect and locate malfunctions.
  • Discuss heating-cooling system malfunctions with users to isolate problems or to verify that malfunctions have been corrected.
  • Record and report all faults, deficiencies, and other unusual occurrences, as well as the time and materials expended on work orders.
  • Test pipe or tubing joints and connections for leaks, using pressure gauge or soap-and-water solution.
  • Adjust system controls to setting recommended by manufacturer to balance system, using hand tools.
  • Recommend, develop, and perform preventive and general maintenance procedures such as cleaning, power-washing and vacuuming equipment, oiling parts, and changing filters.
  • Lay out and connect electrical wiring between controls and equipment according to wiring diagram, using electrician's hand tools.
  • Install auxiliary components to heating-cooling equipment, such as expansion and discharge valves, air ducts, pipes, blowers, dampers, flues and stokers, following blueprints.
  • Assist with other work in coordination with repair and maintenance teams.
  • Install, connect, and adjust thermostats, humidistats and timers, using hand tools.
  • Generate work orders that address deficiencies in need of correction.
  • Join pipes or tubing to equipment and to fuel, water, or refrigerant source, to form complete circuit.
  • Assemble, position and mount heating or cooling equipment, following blueprints.
  • Study blueprints, design specifications, and manufacturers' recommendations to ascertain the configuration of heating or cooling equipment components and to ensure the proper installation of components.
  • Cut and drill holes in floors, walls, and roof to install equipment, using power saws and drills.
  • Wrap pipes in insulation, securing it in place with cement or wire bands.
  • Measure, cut, thread, and bend pipe or tubing, using pipe fitter's tools.
  • Fabricate, assemble and install duct work and chassis parts, using portable metal-working tools and welding equipment.

A.R.S Heating and Cooling


Hvac Installer/Service Tech. - March 2005 - June 2010

  • Discuss heating-cooling system malfunctions with users to isolate problems or to verify that malfunctions have been corrected.
  • Repair or replace defective equipment, components, or wiring.
  • Test electrical circuits and components for continuity, using electrical test equipment.
  • Reassemble and test equipment following repairs.
  • Install auxiliary components to heating-cooling equipment, such as expansion and discharge valves, air ducts, pipes, blowers, dampers, flues and stokers, following blueprints.
  • Assemble, position and mount heating or cooling equipment, following blueprints.
  • Study blueprints, design specifications, and manufacturers' recommendations to ascertain the configuration of heating or cooling equipment components and to ensure the proper installation of components.
  • Fabricate, assemble and install duct work and chassis parts, using portable metal-working tools and welding equipment.
  • Discuss heating-cooling system malfunctions with users to isolate problems or to verify that malfunctions have been corrected.


-

    Williamson County


    Maintenace Tech/Jail.Maint./Hvac - August 2000 - March 2005

    • Repair or replace defective equipment parts, using hand tools and power tools, and reassemble equipment.
    • Perform routine preventive maintenance to ensure that machines continue to run smoothly, building systems operate efficiently, or the physical condition of buildings does not deteriorate.
    • Inspect drives, motors, and belts, check fluid levels, replace filters, or perform other maintenance actions, following checklists.
    • Use tools ranging from common hand and power tools, such as hammers, hoists, saws, drills, and wrenches, to precision measuring instruments and electrical and electronic testing devices.
    • Assemble, install or repair wiring, electrical and electronic components, pipe systems and plumbing, machinery, and equipment.
    • Diagnose mechanical problems and determine how to correct them, checking blueprints, repair manuals, and parts catalogs as necessary.
    • Inspect, operate, and test machinery and equipment to diagnose machine malfunctions.
    • Record type and cost of maintenance or repair work.
    • Clean and lubricate shafts, bearings, gears, and other parts of machinery.
    • Dismantle devices to access and remove defective parts, using hoists, cranes, hand tools, and power tools.
    • Plan and lay out repair work, using diagrams, drawings, blueprints, maintenance manuals, and schematic diagrams.
    • Order parts, supplies, and equipment from catalogs and suppliers, or obtain them from storerooms.
    • Paint and repair roofs, windows, doors, floors, woodwork, plaster, drywall, and other parts of building structures.
    • Operate cutting torches or welding equipment to cut or join metal parts.
    • Align and balance new equipment after installation.
    • Set up and operate machine tools to repair or fabricate machine parts, jigs and fixtures, and tools.
    • Maintain and repair specialized equipment and machinery found in cafeterias, laundries, hospitals, stores, offices, or factories.
    • Lay brick to repair and maintain buildings, walls, arches and other structures.
    • Grind and reseat valves, using valve-grinding machines.
    Education

    National Institute of Technology

    • Experience in heating and air conditioning, maintaing and serviceing residential and commercial units like Trane, Goodman, Carrier, American Standard, Rheem, Ect. Reading and trouble shooting from schematic drawings. Also repairing and servicing compressors and induction motors. EPA certified Type 1 and 2, Also registered Air Conditioning Tech and Refrigeration.
    • References.
    • Daniel Escobar 512-748-7034 Austin Air, Hvac service tech
    • Ivan Sanches 512-508-6359 Austin Air, Hvac start up tech
    • Lisa Alvarez 512-645-8292 Austin Air Service and Install Mang.

    Taylor High School

    • Diploma